#Fetch data from wired server how to#
#Fetch data from wired server manual#
#Fetch data from wired server password#

Note: In this example, Radio 1 (2.4 GHz) is chosen.

Radio 2 (5 GHz) - For wireless clients that operate in the 5 GHz frequency.

Radio 1 (2.4 GHz) - For wireless clients that operate in the 2.4 GHz frequency.

(Optional) If you are using a dual-band access point, click a radio button to choose the Radio Interface that you want to configure. You can enter up to two DNS addresses in the fields provided.

#Fetch data from wired server manual#

In the Domain Name Servers (DNS) area, the radio button for Manual will be automatically selected once the Connection Type is set to Static IP. Note: In this example, 192.168.1.1 is used as the default gateway. Enter the router IP address in the Default Gateway field. (Optional) Enter the subnet mask in the Subnet Mask field. Note: In this example, the IP address used is 192.168.1.112.

Make sure that the IP address you assign is in the same range as your network. (Optional) If you chose Static IP in the previous step, enter the static IP address you want to assign to the WAP in the Static IP Address field. If you performed this step, skip to Step 12.

Static IP- You will be the one to manually assign the IPv4 address to the WAP.

DHCP - The access point acquires its IP address from a Dynamic Host Configuration Protocol (DHCP) server on the network.

Click a radio button to choose the Connection Type. Note: If you want to use IPv6 Addressing instead, click here for instructions. Note: If you are using the WAP121, WAP321, WAP371, WAP551, or the WAP561, choose LAN > VLAN and IPv4 Address. In the navigation area, choose LAN > IPv4 Setting.

#Fetch data from wired server password#

Note: The default username and password of the default user for Cisco Access Points is cisco/cisco. Also, you can create a different username and password to each user. These users are the ones authorized to access the web-based utility through their authentication keys but only one of these users can have the Read/Write privilege level.

Note: You can set up to five users to each access point that you are going to add to the network. In the authentication window, enter the username and password of the WAP in the Username and Password fields, respectively. This is the default IP address of Cisco Access Points. Note: In the image above, 192.168.1.245 is used as an example of the IP address. These applications will help you check the IP addresses and other information of the access point and other Cisco devices within your network. Note: In the event that you do not know the IP address of your WAP, you can use the Cisco FindIT Discovery Tool or the Cisco FindIT Network Management tool if these applications are installed in your network.

On the wireless computer, access the web-based utility of the WAP by launching a web browser and entering the IP address of the WAP in the address bar. Note: The default Service Set Identifier (SSID) or wireless network name of the Cisco Access Point is ciscosb. Connect your wireless computer to the wireless network that the WAP is broadcasting. Note: If your WAP does not have Power over Ethernet (PoE) capability, connect the AC power adapter to the WAP and plug it to the power outlet. Connect the WAP to your router or switch using the supplied Ethernet cable. The images used in this article are taken from the WAP361. Note: Images may vary depending on the exact model of your WAP. Applicable DevicesДЄdd a Wireless Network to an Existing Wired Network Set up the Wireless Network

#Fetch data from wired server how to#

The objective of this article is to show you how to add a wireless network to your existing wired network using a wireless access point. In the right portion, a wireless network shows two wireless computers connected to a WAP.

It consists of four wired computers connected to a switch, which is connected to a router. In the network diagram above, the left portion shows an existing wired network. It is like creating another network only for wireless devices but still be a part of your existing wired network such as shown in the diagram below. Adding a WAP to your existing wired network is useful to accommodate those devices that are only capable of wireless connection. A Wireless Access Point (WAP) is a networking device that allows wireless-capable devices to connect to a wired network.